DeSoto Carburetors for old Desoto's : DESOTO MODEL SD LATE 1933 Previous | Home | Next

De Soto "SD" SIX-EbA3 and EbA4-List Price $29.40
WHEN SERVICING, USE GASKET ASSORTMENT No. 606-List Price $0.50 All Prices Subject to Prevailing Surcharge
PARTS PRICE LIST List Price
Pump spring 15
Lock washer (11/64 inch I. D.) 02
Lock washer (9/32 inch I. D.) 02
Flange stud lock washer 02
Lock washer (15/64 inch I. D.) 02
Clamp screw 07
Body flange attaching screw 07
Throttle adjusting screw 07
Air horn attaching screw 07
Choker lever stop screw 07
Throttle valve screw 2 for 07
Flange stud nut 07
Ball 04
Pump connector link I5
Pump operating _ 20
Body gasket 15
Body flange gasket 07
Idle orifice tube and plug assembly 30
Main vent tube and plug assembly 30
Step-up valve assembly 60
Pump rod pin 04
Pin spring ---------- -°--° 02
Main metering screw-one size lean (E6A4)- - .45
Main metering screw-two sizes lean (E6A3) 45
Main metering screw-two sizes lean (E6A4) 45
Main metering screw-standard (E6A3) 45
Main metering screw-one size rich (E6A4) - .45
Main metering screw-standard (E6A4) 45
Main metering screw-one size lean (E6A3)..--.- 45
Main metering screw-one size rich (E6A3) 45
Step-up piston ass'y (superseded by 160-23S) 45
Pump piston (outer( 60
Pump piston - 20
Pump piston, needle and plug assembly 45
Step-up piston assembly 45
Power orifice (step-up jet) I5
Note: Use carbureter No. E6A4 when replacing carbureters Nos. E6A or E6A3.
*Soak in 90 proof denatured alcohol for 15 minutes, install on part and let dry before using.
*This bushing should be installed when servicing carbureters not so equipped (Refer to Carter General Service Bulletins "Chrysler Corp. No. 18" dated June 5, 1933, and No. 18-A dated July 7, 1933).
tNo. 30A-35 Idle Adjustment Screw and No. 61-57 Idle Adjustment Screw Spring were used on the first 1700 E6A3 carbureters manufactured. After that No. 30A-37 Idle Adjustment Screw and No. 61-84 Idle Adjustment Screw Spring were used.
I-89S Body flange assembly _ $3.30 61-85
IA-21 Flange gasket .07 86-10
2-71 Throttle valve .30 86-II
3-179S Throttle shaft and arm assembly .90 86-15
4-220S Throttle lever assembly_ .60 86-17
6-104S Air horn assembly 3.70 101-12
7-52S Choker valve assembly .75 101-18
11B-16 Pump jet plug .I5 101-31
116-31 Idle hole plug .... -15 101-35
I B-40 Rivet plug (Sup. by IIB-79) .04 101-38
11B-41 Rivet plug .04 101-39
IIB-50 Idle vent screw plug .15 I05A-13
I16-55 Needle retainer plug .07 116-13
1 8-79 Rivet plug .... .04 117-24
14-1415 Choker lever and shaft assembly .60 117-25
17-30 Pump piston needle .20 121-17
20-3 I Needle seat gasket .07 121-18
20-32 Metering screw gasket .07 123-IBS
20-37 Siep-up piston washer .07 I45-14S
20-38 *Pump piston needle seat gasket .07 149-2 I S
21-49S Float and lever assembly 1.20 150-35
24-19S Float lever pin and plug assembly .I5 I50A-10
25-50S Needle and seat assembly 1.20 159-19
25-52S Pump piston needle seat and gasket ass'y- .45 159-19
30A-35 tIdle adjustment screw .45 159-20
30A-37 Idle adjustment screw .45 159-22
38A-26 *Step-up passage bushing ................................ 159-22
39-11 Valve attaching screw 2 for .07 159-23
43B-10 Pump piston rod washer .07 159-23
48-40 Pump jet, .0354". .20 159-27
49-89 Step-up push rod ----° .15 160-14S
49-96 Pump piston rod - .04 160-17
61-57 tidle adjustment screw spring_ .07 160-18
61-58 Throttle lever adjusting screw spring .07 160-19S
61-61 Siep-up spring .07 160-235
61-84 Idle adjustment screw spring .07 162-13
Copyright 1933